ColecoVision Instructions
 
             for the
 
    Super Action Controller Set         
               
-------------------------------------------------------------------------------

The Most Sophisticated Video Game Controllers Yet!


HOOKING UP YOUR SUPER ACTION CONTROLLERS

1. Unplug and remove the Hand Controllers from the ColecoVision Console
   unit, and set them aside.

2. Plug a Super Action Controller into the Port 1 socket (rear socket) of your
   ColecoVision Console unit. Port 1 Controller is used for One-Player Games.

3. Plug a Super Action Controller into the Port 2 socket (front socket) of your
   console unit. See Fig. 1.

   The Controller jacks will fit only one way-- DO NOT FORCE them into the
   controller sockets.

4. Included with your controllers are Snap on Pistol Grips. The Snap on Pistol
   Grips make for easy handling and comfortable use. They are included to 
   accommodate large size hands. Simply snap the Pistol Grips over the hand 
   grip on your Super Action Controller as shown in Fig. 2.

   Now you are ready to begin playing your game! BE SURE THAT THE COLECOVISION 
   UNIT IS OFF BEFORE INSERTING OR REMOVING CARTRIDGE. Refer to your GAME 
   CARTRIDGE Instruction Guide for game play instructions.

   WARNING: ALWAYS UNPLUG THE POWER SUPPLY FROM THE 110/120 VOLT OUTLET WHEN 
   YOU HAVE FINISHED PLAYING.


CARE OF YOUR GAME

Treat your COLECOVISION SUPER ACTION CONTROLLERS with care.

Before inserting or removing GAME CARTRIDGE, always make sure that the POWER 
SWITCH on CONSOLE unit is turned "OFF".

Always unplug the POWER SUPPLY from the 110/120 volt outlet when you have 
finished playing. IMPORTANT: ONLY CONNECT THE CONSOLE POWER SUPPLY UNIT INTO A
110/120 VOLT HOUSEHOLD ELECTRICAL SERVICE, OTHERWISE SERIOUS DAMAGE MAY OCCUR 
TO ELECTRICAL PARTS OF THE SYSTEM.

Do not drop or bang CONTROLLERS, or COLECOVISIONTM CONSOLE unit.

Do not use sharp or pointed object to activate KEYPAD BUTTONS.

Do not store or leave CONTROLLERS, CONSOLE and accessories where they may be 
subject to heat build-up.

Keep away from moisture. Do not immerse CONTROLLERS or CONSOLE in water Use a 
soft, slightly damp cloth to wipe clean.

WARNING: Before cleaning CONTROLLERS, CONSOLE and accessories, turn POWER 
SWITCH to "OFF" and disconnect the AC POWER SUPPLY unit from the 110/120 volt 
wall outlet.

Do not attempt to repair SUPER ACTION CONTROLLERS. They do not contain any 
owner serviceable parts. Refer to your TROUBLESHOOTING section, if not 
successful refer to LIMITED WARRANTY

NOTICE

This game generates and uses radio frequency energy and if not installed and
used properly, that is in strict accordance with the instructions, may cause 
interference to radio and television reception. It has been type tested and
found to comply with the limits for a Class B computing device in accordance 
with the specifications in Subpart J of Part 15 of FCC Rules, which are 
designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will 
not occur in a particular installation. If this game does cause interference to
radio or television reception, which can be determined by turning the game off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:

Reorient the TV antenna.

Relocate the game with respect to the TV

Move the game away from the TV

Plug the game into a different outlet so that game and TV are on different 
branch circuits.

If necessary, the user should consult the dealer or an experienced radio/
television technician for additional suggestions. The user may find the 
following booklet prepared by the Federal Communications Commission helpful:

"How to Identify and Resolve Radio TV Interference Problems".

This booklet is available from the U.S. Government Printing Office, Washington,
DC 20402, Stock No. 004-000-00345-4.


TROUBLESHOOTING

 SYMPTOM                             REMEDY
----------------------------------  -----------------------------------------
 Hand Controller not functioning     Check and see if the Controller Jack
 correctly                           is firmly seated in the socket of the
                                     Console unit.

                                     If the other hand controller is work-
                                     ing correctly, simply switch the
                                     working controller and firmly insert
                                     the jack into the non-working plug. If
                                     working controller fails to work cor-
                                     rectly, the Console unit is probably
                                     faulty. If working controller works
                                     properly in other jack, the first con-
                                     troller is probably faulty.